Pass CompTIA PD1-001 Exam Info and Free Practice Test [Q122-Q142]

Rate this post

Pass CompTIA PD1-001 Exam Info and Free Practice Test

New 2022 Latest Questions PD1-001 Dumps – Use Updated CompTIA Exam

NEW QUESTION 122
A client has a fax machine and their incoming faxes print out corrupted images. Also, the outgoing faxes arrive at their destination with corrupted images. A technician has checked the phone cable and it is intact, the device settings are correct and the test prints of the device are printing ok.
Which of the following could be the cause?

Improper paper type

Electronic noise on the phone line

Insufficient memory in the fax machine

Bad/damaged print engine

NEW QUESTION 123
Which of the following are typical symptoms of a printer when using card stock that is heavier than specified? (Select TWO).

Media will not transfer the latent image

Media feed rollers wear out early

Media will melt on the fuser and jam the machine

Media will not initially feed/pick up from the media tray

Media will be picked up in multiple sheets and jam the printer

NEW QUESTION 124
Which of the following components provides basic power for the device?

Charge Unit

Charge Coupled Device (CCD)

Low Voltage Power Supply (LVPS)

High Voltage Power Supply (HVPS)

NEW QUESTION 125
The latent image is written on which of the following components?

Transfer belt

Photoconductor

Developer unit

Charge roller

NEW QUESTION 126
Which of the fol owing components are used to create the latent image on the photoconductor?
(Select TWO).

Charge Couple Device (CCD)

Developer

Light Emitting Diode (LED)

Transfer roller

Laser

NEW QUESTION 127
Firmware typically resides in which of the following components on an MFD?

In a CCD

On a USB flash drive

In the hard drive

On a circuit board

NEW QUESTION 128
After installing a new printer, a customer finds that it prints random characters. The customer has updated the driver with an update wizard. Which of the following should the technician recommend that the customer do next?

Check the driver port type.

Change the DNS address.

Reload the application software.

Uninstall and reload the driver.

NEW QUESTION 129
On a digital printer utilizing a negative main charge, which of the following image quality problems would be expected if the laser unit was not functioning?

Gray background

Blank image

Poor focus

Black image

NEW QUESTION 130
Which of the following stages of the print process involve the print media? (Select TWO).

Transfer

Developing

Charge

Fusing

Writing

NEW QUESTION 131
Which of the following components fixes/bonds toner to the print media?

Laser Unit

Charge Assembly

High Voltage Power Supply

Fusing assembly

NEW QUESTION 132
After repairing media tray one and three on a printer, there are stil some multi-feeding issues from tray two. The technician does not have the appropriate parts to complete this repair. Which of the following is the BEST way to communicate this to the client?

Media trays one and three are working now. Media tray two jams intermittently. The parts have been ordered and will be installed tomorrow.

Media tray one and three and up and running. Media tray two works some of the time. Please use only tray one and three.

Media trays one and three are working now; however, tray two jammed several times. It cannot be fixed now because parts are not available. Please use the other two trays and place another service call for the other tray.

Everything is replaced and working fine now. If anything else is required, please call.

NEW QUESTION 133
A dislodged separation pawl in the fuser is MOST likely going to:

lead to a decrease in fixer pressure.

cause the machine to display a service code.

lead to an increase in fixer temperature.

cause paper jams.

NEW QUESTION 134
A technician encounters an extremely irate client. During initial conversation the client makes it clear they are very angry with the situation and the technician. The client becomes aggressive, unreasonable, verbally abusive, loud and very rude to the technician. Which of the responses below is the BEST way to react?

Try to reason with and calm the client by explaining why the unit could have malfunctioned, how long it will take to repair the unit and how the situation is not as bad as the client perceives it to be.

Walk over to the device and disassemble it. Then turn around and leave while telling the client to repair the unit themselves.

Politely and quietly, turn around and leave. The technician should immediately contact their management to inform them of the situation and have them follow up with the clients company.

Explain how the issue is not the technicians fault and the client needs to step away and let the device be assessed so the issue can be fixed.

NEW QUESTION 135
Which of the following is a recommended cleaner for rubber feed rollers?

Bleach

Iodine

Water

Glass cleaner

NEW QUESTION 136
Which of the following type of jack is used for a fax line?

RJ-11

RJ-13

RJ-44

RJ-45

NEW QUESTION 137
The residual toner remaining on a photoconductor is removed by which of the following laser printer components?

Fuser unit

Developer unit

Cleaning unit

Transfer unit

NEW QUESTION 138
A customer places a service call stating they cannot send or receive any faxes. The device is able to make copies though. Which of the following should the technician check?

The paper feed system

The fax line for a dial tone

The ADF for proper operation

The power source

NEW QUESTION 139
A customer desires that all print jobs to their color MFD product by default come out in black and white. Which of the following would be the default setting a technician would use?

Multifunction device

TCP/IP settings

Print driver

Color management

NEW QUESTION 140
Which of the following has the LEAST effect on color perception of a color print?

The media type the customer uses to print on

The font type used in the customers documents

The amount of sunlight entering the customers office

The type of light bulbs in the customers office

NEW QUESTION 141
Which of the following is the MOST suitable way of providing ESD protection when working on a machine?

Use of a wrist strap

Wearing gloves

Wearing rubber soled shoes

Grounding the machine

NEW QUESTION 142
Adding more memory to a printer will:

extend the life of the printer consumables.

increase the load on the network when printing.

decrease the number of paper jams.

decrease the print job start time.

Latest PD1-001 Exam Dumps CompTIA Exam: https://www.pdf4test.com/PD1-001-dump-torrent.html

Free certification test prep

Pass CompTIA PD1-001 Exam Info and Free Practice Test [Q122-Q142]

Leave a Reply Cancel reply